Submit our quick form and get quotes now!
4 min read
4 min read
Interior renovationsHow to Apply Drywall Joint Compound
Applying drywall joint compound is an art that requires patience and meticulousness. Contrary to other types of renovation projects, this task is accessible to anyone. However, in order to ensure good results, it is important to follow certain guidelines.
The job will last at least 4 days, as three separate coats of drywall compound will have to be applied, with an 18 to 24 hour waiting period between each coat. If you are inexperienced, you will have to work more slowly to apply the product in the right way.
Spatula;
Two trowels (different sizes);
Drywall tape;
Platter or any flat-surfaced object (to mix the drywall compound);
Drywall compound;
Sandpaper;
Sanding block and sponge;
Personal protection equipment (mask, gloves);
Washcloths;
Container filled with tepid water.
Start by emptying the room where you will be working and protecting the surfaces that cannot be removed. It is also recommended that you cover the furniture in rooms nearby, as the dust has a way of spreading around.
If necessary, install metal corner beads, which will serve to unite gypsum panels that meet at the exterior corner of two wall sections (see the photo below). Be careful not to nail or screw them in too tightly, as this could cause them to warp.
Photo: Today's homeowner
Put a little bit of the drywall compound on your platter. Next, using your trowel (the smaller one), take a bit of the drywall compound. Starting from the middle part of the joint, spread the product over the whole gap. Once you have covered the complete section, install some drywall tape.
Stretch the paper as much as possible and spread a small coat of drywall compound on top, whilst carefully pressing on the paper to create a nice homogenous surface. As you complete this part of the process, be sure to remove any extra compound that has gathered on the sides. Repeat this operation until you have covered each one of the joints. Once you have finished applying the first coat, inspect the whole area and remove any excess compound.
Photo: Flickr- Georgia National Guard
Before you start working on the second coat, sand the joints very carefully, making sure not to perforate the drywall tape. For the upcoming steps, we recommend that you use a larger trowel that will serve to eliminate marks and delineations. Apply thin coats and don’t forget to clean your tools after each use.
* Notes: If the drywall joint compound is too dense, you can dilute it using a small quantity of tepid water. Be careful with air bubbles that tend to form behind the tape. If bubbles appear, the joint will have to be redone.
The previous instructions mostly applied to “standard” joints. However, interior wall corners don’t exactly work the same way. You’ll have to be very careful in trying to avoid drywall compound accumulation in these corners. Spread the joint compound on both sides of the corner.
Next, fold the drywall tape in two and install it in the corner, starting from the top. Press firmly, using your trowel and make sure that both sides are even. For the next two coats, follow the same instructions as written in the paragraph above. In places where there are screws, insert a bit of drywall compound directly into the holes. Press strongly to even out the product.
Once the last coat has had the time to dry, it’s time to work on giving these joints a nice finish. Using your sanding tools, try to even out the surfaces in order to get a nice, smooth result.
After you’ve finished sanding the joints, you’ll be left with plenty of dust throughout the room. Before you start vacuuming, start the cleaning process by removing most of the dust with a broom and a wet cloth. Since the dust particles are extremely small, they may end up clogging your vacuum cleaner so it’s best to use it as little as possible. Once you’re done cleaning, you’ll be ready to start painting!
RenoQuotes.com will put you in contact with 3 reliable contractors for your drywall plastering project. Fill in the form on our homepage (it only takes a few minutes), and you will receive quotes from trusted professionals.
Last modified 2023-11-07
The latest industry news, interviews, technologies, and resources.
Léa Plourde-Archer • 07 Nov 2023
What is radon ingress? How do you know if your house is affected by this type of problem and if so, what can you do about it?
RenoQuotes.com • 15 Apr 2024
Global warming, deforestation, acid rain, plastic microbeads, oil spills, blue-green algae, holes in the ozone layer, endangered species, ecosystem destruction, heat islands, public health issues… Clearly, the 21st century sees no shortage of environmental problems.
RenoQuotes.com • 07 Nov 2023
Among the aspects that make guests enter and return to a restaurant, there is the way they are treated upon arrival, the quality and variety of the dishes offered, but also the comfort of the place. It's on this specific point that we will elaborate in this article.
Amanda Harvey • 07 Nov 2023
As one of the most frequented rooms in the home, the bathroom needs a little bit of TLC every once and a while. As a result, it's necessary to offer up a bit of modern love as well as tend to the rougher edges that face wear and tear over the years.
RenoQuotes.com • 07 Nov 2023
The climate change issue is now more relevant than ever, and the construction industry is facing a critical challenge: reducing its carbon footprint. As such, net-zero emissions, meaning achieving a balance between carbon emissions generated by construction activities along mitigation efforts are now becoming a priority. In this article, we’ll delve into the different strategies and measures implemented to achieve this noble goal.